BMW 3 series E30

Since 1983-1994 of release

Repair and car operation



BMW E30
+ 1. The maintenance instruction
- 2. Maintenance service
   2.2. Recommended lubricants and liquids
   2.3. Periodicity of service
   2.4. Features of routine maintenance of the car
   2.5. The general data on additional maintenance service
   2.6. Check of level of liquids
   2.7. Check of a condition of tyres and pressure in tyres
   2.8. Oil replacement in the engine and the oil filter
   2.9. Check and restoration of level of a liquid in a wheel
   2.10. Check of level of a liquid in automatic transmission
   2.11. Shift of wheels
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check, adjustment and replacement of belts of a drive of hinged units
   2.14. Check and adjustment of turns and quality of a mix FROM) idling
   2.15. Check of a condition and battery gymnastics
   2.16. Check and replacement of candles
   2.17. Check of high-voltage wires, бегунка and distributor covers
   2.18. Check of level of oil in a manual transmission
   2.19. Check of level of oil in the main transfer
   2.20. Check and adjustment of backlashes in valves (except engine M40)
   2.21. Draught throttle заслонки
   2.22. Replacement of the air filter
   2.23. Check of fuel system
   2.24. Check of system of cooling
   2.25. Exhaust system check
   2.26. Check of shock-absorbers, a suspension bracket and a steering
   2.27. Check of covers of semiaxes
   2.28. Check of brakes
   2.29. Check of brushes of screen wipers
   2.30. Liquid replacement in automatic transmission and the filter
   2.31. Cooling system – replacement of a liquid and washing
   2.32. Replacement of the fuel filter
   2.33. Oil replacement in a manual transmission
   2.34. Oil replacement in картере the main transfer
   2.35. Check of system of catching of steams of gasoline (EVAP-system)
   2.36. Installation of the light alarm system of necessity of servicing
   2.37. Replacement of a gear belt
+ 3. The engine
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmissions
+ 9. Coupling
+ 10. Brake system
+ 11. A running gear
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice
Мастер леса выравнивание участка.



2.14. Check and adjustment of turns and quality of a mix FROM) idling
THE GENERAL DATA

The prevention

Before check the engine should be heated-up, the ignition moment is adjusted, and backlashes in valves to correspond to norm (except for self-regulated valves). All consumers should be disconnected.


Carburettor engines

PERFORMANCE ORDER
1. Connect a tachometre and a gas analyzer.
2. Warm up the engine and translate on idling.
3. Adjustment of turns is supposed only on carburettors 2В4. The special screw (in a photo) is For this purpose provided.
4. If on the engine with the carburettor 2ВЕ turns low and conducting is serviceable to raise them it is possible connection of the additional resistor in a management chain (it is carried out in car-care centre BMW).
5. Quality of a mix is regulated by the special screw (it is specified by figure 2).

System of injection L-Jetronic

The special tester is necessary for check WITH which gauge is rolled in a final collector (is supposed to use the analyzer with a probe which is entered into an exhaust pipe, however on models with neutralizer this device will not give comprehensible results).

PERFORMANCE ORDER
1. Idling turns are regulated by the screw on a throttle branch pipe (preliminary it is necessary to remove заглушку the screw).
2. Quality of a mix (WITH) is regulated by the screw on a stream measuring instrument special key BMW 13 1 060.

System of injection Motronic

The special tester is necessary for check WITH which gauge is rolled in a final collector (is supposed to use the analyzer with a probe which is entered into an exhaust pipe, however on models with neutralizer this device will not give comprehensible results).

PERFORMANCE ORDER
1. If idling turns differ from normal (adjustment is provided with automatically processor block) check up tightness of a joint of an inlet collector and also an air regulator of idling.
2. Quality of a mix (WITH) is regulated by the screw on a stream measuring instrument шестигранным a key.
3. Remove заглешку the adjusting screw on a stream measuring instrument.
4. Adjust WITH.
5. Put заглушку into place.